Artwork & Topcoat Epoxy resin, up to 1 cm

Mixing ratio by weight: A : B = 100 : 50
Color: Ultra clear (diamond clear) in both components
Processing time 100 g at 25°C: 15 minutes*
Curing time at 25°C: 4 hours*
Fully cured after: 1 day
UV blocker: yes
Hardness: Shore D90
Solvent-free
Self-leveling
Excellent self-venting for a bubble-free finish
Density: 1.09 g / cm³
Viscosity: 3000 - 4500 cPs
Highly viscous
Temperature resistant up to: 140°C***
Minimum layer thickness: 0.05 cm
Maximum layer thickness: 1.0 cm
Single processing quantity max.: 10 kg

To achieve this high temperature resistance, the epoxy resin must be baked for 1.5 hours at 60°C. Otherwise, the temperature resistance is approx. 90°C.

Please note that we are talking about temperature resistance here.

This means that the epoxy will not scorch or crack at this temperature. However, the epoxy may temporarily soften and nick due to the weight! This makes all types of epoxy less suitable for use as coasters.

With a larger quantity, the processing time and the curing time are shorter!

If you have little experience, we recommend not processing the maximum amount at once.

If you still want to do this, work at 18°C with a large diameter mixing bucket and take into account a very short processing time!

For 10 kg please pour a layer thickness of maximum 0.5 cm.

Make sure the surface is dense and non-porous. This can cause air bubbles in the epoxy. To do this, use a thin layer of epoxy or primer. Always use protective gloves and goggles when handling this material. Process the resin at room temperature (18 - 25 ° C) and humidity less than 70%. To avoid deformation of the surface, the temperature must remain constant throughout the curing process. Also avoid direct sunlight through a window and avoid drafts.

Mix the A and B components in the correct ratio (A : B = 100 : 50 by weight) and mix well. Allow enough time for mixing (2 - 3 minutes) and make sure to include the corners and bottom of the mixing bowl. Optionally, you can pour the whole thing into a second bowl and mix again.

Now add all the colour effects and stir again. Allow air bubbles to escape for a minute. If necessary, help by vibrating/rattling the cup. Make sure the product does not get too hot!

The epoxy resin is now ready for use. Apply the mixture with a brush/roller or pour the mixture with a thin stream into the desired mold or prepared model.

Make sure to use a large-bottomed mixing bowl for larger quantities. Avoid a thick layer in the mixing bowl as this will heat up very quickly!

Removing air bubbles is best done with an epoxy deaerator or with a flame. Please do not use flames if you have diluted the epoxy with alcohol or other flammable products.

If you want to apply the resin in several layers (multi-layer work)

Wet on wet:

When pouring a second layer of liquid into a first layer of epoxy liquid, you need to make sure the exothermic reaction has completely worn off. An exothermic reaction is a reaction that releases energy. In this case, heat. If you want to be sure, wait until the second layer is no longer sticky, but you still see a fingerprint in the epoxy.

wet on dry

The previous layer must be sanded and made free of dust and grease.

reaction product:
reaction products with ammonia
Bisphenol-A-(epichlorohydrin; formaldehyde, polymer with (chloromethyl)oxirane and phenol.
Contains:
Propylidynetrimethanol, propylated, C13/C15-alkyl glycidyl ether; reaction product.
Danger:

H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H302+H312 Harmful if swallowed or in contact with skin.
H318 Causes serious eye damage.
H411 Toxic to aquatic life with long lasting effects.

Danger:
P102 Keep out of the reach of children.
P270 Do not eat, drink or smoke when using this product.
P301+P310 IF SWALLOWED:Immediately call a POISON CENTER/
Doctor/call.
P280 Wear protective gloves/ protective clothing/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if possible. Continue rinsing.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P501 Dispose of contents/container in accordance with local/regional/national/
Dispose of in accordance with international regulations.
EUH205 Contains epoxy compounds. May produce an allergic reaction.
P271 Use only outdoors or in a well-ventilated area,
P273 Avoid release to the environment.
P280 Wear protective gloves/ protective clothing/eye protection/face protection.
P301+P330+P331 IF SWALLOWED: Rinse mouth. DO NOT induce vomiting.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.

If you see that the resin component is white and flaky, then this is crystallized resin.

Crystallization of epoxy resin is a physical process caused by external factors such as cold or temperature fluctuations. It is fully reversible and is comparable to the freezing of water. The main causes are

1. Temperatures that are too low: crystals can form at temperatures below 15 °C during storage or transport.

2. Temperature fluctuations: The formation of crystals is driven by regular alternation between hot and cold.
High resin purity: Epoxy resin with high purity is more susceptible to crystallization.
3. Low viscosity: Resins with low viscosity tend to form crystals.

This reaction occurs at extremely low temperatures and can be reversed by a water bath (approximately 60 minutes/50 °C).

Simply place the sealed resin container in the water bath. Then allow the resin to cool to normal room temperature.