Deep Casting Epoxy Resin, up to 5 cm

Mixing ratio by weight: A:B = 100:50
Color: Ultra Clear (Diamond Clear) in both components
Processing time 100 gr. at 25°C: 6 hours*
Curing time at 25°C: 36-48 hours*
Fully cured after: 4 days
UV blocker: yes
Hardness: Shore D 82
Density: 1.09 g/cm³
Viscosity: 300-600 cPs
low viscosity
Solvent-free
Self-leveling
Excellent self-venting for bubble-free finish
Temperature resistant up to: 80°C
Minimum layer thickness: 1 cm
Maximum layer thickness 5 cm
The maximum casting height of 5 cm is highly dependent on the ambient temperature. If the temperature exceeds 22°C, the maximum casting height is reduced

With a larger quantity, the processing time and the curing time are shorter!

If you have little experience, we recommend not processing the maximum amount at once.

If you still want to do this, work at 18°C with a large diameter mixing bucket and take into account a very short processing time!

Important: The higher the room temperature (>21 °C) and the larger the amount of casting, the lower the casting height should be. Epoxy resin reacts faster, especially in summer, which can lead to undesirable results.

With large quantities, such as 30 kg, overreactions can occur despite a reduced layer height. We therefore recommend pouring in two layers or using a resin system for larger layer thicknesses. Note: Temperature, pouring volume and layer height are crucial for best results.

Make sure the surface is dense and non-porous. This can cause air bubbles in the epoxy. To do this, use a thin layer of epoxy or primer.

Always use protective gloves and goggles when handling this material. Process the resin at room temperature (18 - 25 ° C) and humidity of less than 70%. To avoid deformation of the surface, the temperature must remain constant throughout the curing process. Also avoid direct sunlight through a window and avoid drafts.

Mix the A and B components in the correct ratio (A : B = 100 : 50 by weight) and mix well. Allow enough time to mix (2 - 3 minutes) and make sure to include the corners and bottom of the mixing bowl. Optionally, pour the whole thing into a second bowl and mix again. Now add all the color effects and stir again. Allow air bubbles to escape for a minute. If necessary, help by vibrating / rattling the cup. Make sure the product does not get too hot!


The epoxy resin is now ready to use. Apply the mixture with a brush/roller or pour the mixture with a thin stream into the desired mold or prepared model.


Make sure to use a large-bottomed mixing bowl for larger quantities. Avoid a thick layer in the mixing bowl as this will heat up very quickly!

Removing air bubbles is best done with an epoxy deaerator or with a flame. Please do not use flames if you have diluted the epoxy with alcohol or other flammable products.


If you want to apply the resin in several layers (multi-layer work):

Wet on wet:

When pouring a second layer of liquid into a first layer of epoxy liquid, you need to make sure that the exothermic reaction is completely worn off. An exothermic reaction is a reaction that releases energy. In this case, heat.
If you want to be sure, wait until the second coat is no longer tacky but you still see a fingerprint in the epoxy.

Wet on dry:

The previous layer must be sanded and made free of dust and grease.

reaction product:

reaction products with ammonia

Bisphenol-A-(epichlorohydrin; formaldehyde, polymer with (chloromethyl)oxirane and phenol.

Contains:

Propylidynetrimethanol, propylated, C13/C15-alkyl glycidyl ether; reaction product.

Danger:
H315 Causes skin irritation.

H317 May cause an allergic skin reaction.

H319 Causes serious eye irritation.

H302+H312 Harmful if swallowed or in contact with skin.

H318 Causes serious eye damage.

H411 Toxic to aquatic life with long lasting effects.

Danger:

P102 Keep out of the reach of children.

P270 Do not eat, drink or smoke when using this product.

P301+P310 IF SWALLOWED:Immediately call a POISON CENTER/
Doctor/call.

P280 Wear protective gloves/ protective clothing/eye protection/face protection.

P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if possible. Continue rinsing.

P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.

P501 Dispose of contents/container in accordance with local/regional/national/
Dispose of in accordance with international regulations.

EUH205 Contains epoxy compounds. May produce an allergic reaction.

P271 Use only outdoors or in a well-ventilated area,

P273 Avoid release to the environment.

P280 Wear protective gloves/ protective clothing/eye protection/face protection.

P301+P330+P331 IF SWALLOWED: Rinse mouth. DO NOT induce vomiting.

P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.

NB:
When the resin component is white and flaky, it is crystallized resin .

The crystallization of epoxy resin is a physical process caused by external factors such as cold or temperature fluctuations. It is fully reversible and comparable to the freezing of water.

The main causes are:

• Temperatures too low : During storage or transport, crystals may form at temperatures below 15 °C.

• Temperature fluctuations : Regular alternation between hot and cold promotes crystal formation.

• High resin purity : Epoxy resin with high purity has a greater tendency to crystallize.

• Low viscosity : Resins that are thin form crystals faster.

This process occurs mainly at very low temperatures and can be reversed by placing the resin in a water bath (approximately 60 minutes at 50 °C).

👉 Simply place the closed wax container in the water bath. Then let the wax cool down to normal room temperature .